Description
EL365007X MIDLAND "CERTIFIED REMANUFACTURED" AIR BRAKE COMPRESSOR – CAT C7 & C9 ENGINE – 2-BOLT FLANGE
PART NUMBER(S):
Fleet Products: KN365007X (Remanufactured) | OE: CAT: 273-6053, 276-0806, 311-4562, 273-6051, 10R-5296, 10R-9391, 296-7668, 314-6149, 344-6362, 304-9982 | MIDLAND: N7212FM
DESCRIPTION:
Model: Midland EL365 Style 2-Bolt Flange Mount
Vehicles: Caterpillar C7 & C9 Diesel Engines (2004–2010)
• 11-tooth spline gear with 2-bolt flange mounting
• 16.1 CFM airflow capacity
• Flow Capacity: 10.5 CFM @ 1800 RPM and 125 PSI
• Swept Volume: 365CC
• Piston Diameter: 2.75 in
• Stroke: 1.87 in
• Loaded HP: 4.5 HP | Unloaded HP: 1.4 HP
• Twin-cylinder design for reduced vibration and pulsation
• Rear head configuration with right-hand rotation
• Check valve pre-installed
• Water-cooled block and head
• Drive-thru torque capacity: 150 ft-lb (203.4 Nm)
• Maximum RPM: 3000
• Inlet Pressure: Naturally aspirated to 60 PSI (turbo compatible)
• Exhaust Pressure: 8.6 bar (125 PSI)
• Oil Temp: 99°C (210°F) @ 2.4 bar (35 PSI)
• Coolant Temp: 88°C (190°F) @ 0.83 bar (12 PSI)
• Ambient Inlet Temp: 30–32°C (86–89.6°F)
• Accessory mounting flange: SAE “A” 2-bolt
• Includes pressure relief valve and installation gaskets
• Supplied without governor and manifolds
Applications:
Used on Caterpillar C7 and C9 engine platforms in medium- and heavy-duty trucks, vocational vehicles, and construction equipment. This EL365 compressor provides consistent high air output for demanding air brake systems and supports accessory drive-through applications such as hydraulic or steering pumps.
CROSS-REFERENCE(S):
10R9391, 5396-EL365007X, N7212FM, EL365007X, N7212AS, N7212CB, N7212EH, N7212FF, 10R5296, 296-7668, 314-6149, 344-6362, 2967668, 3146149, 3446362, 273-6053, 276-0806, 311-4562, 273-6051, 10R5296, 10R-5296, 10R9391, 10R-9391, 296-7668, 2967668, 314-6149, 3146149, 344-6362, 3446362, 304-9982
A cross-reference listing means this part is a suitable replacement for the part numbers listed. Please confirm all ports and dimensions match your application before installing.
IMPORTANT INSTALLATION NOTES:
âś” Use clean, filtered engine oil (≤40 micron); maintain proper oil pressure and temperature to prevent wear
âś” Ensure coolant flow (min. 2.5 GPM) with correct routing; do not exceed 266°F (130°C)
âś” Maintain proper oil drain through mounting flange; do not block passages or use sealants
âś” Keep intake restriction below 20" HO and use high-efficiency air filtration
âś” Use correct discharge line size (min. 0.547" ID) and route downward to avoid buildup
âś” Do not exceed 190 PSI discharge pressure or 3000 RPM operation
âś” Maintain proper tilt limits to ensure lubrication (max 30° rotation, 10° static tilt)
âś” Use minimum 1/4" ID governor line; keep short and unrestricted to avoid pressure fluctuation
Warranty Information
